54 found, showing page 2 of 4
FINISH TRIM SCREW 8 X 2"
FINISH TRIM SCREW 8 X 2"
View Details
Call for Price
INSERT BIT 2" TORX T-10 2PK
INSERT BIT 2" TORX T-10 2PK
View Details
Call for Price
INSERT BIT 2" TORX T-15 2PK
INSERT BIT 2" TORX T-15 2PK
View Details
Call for Price
INSERT BIT 2" TORX T-30 2PK
INSERT BIT 2" TORX T-30 2PK
View Details
Call for Price
R4 FRAMING SCREW 8 x 1-1/4" 5-LB
GRK's RSS screw is made of specially hardened steel to provide you with high tensile, torque and shear strength. The sharp threads and points bite instantly into the material (including hardwood), reducing the splitting effect due to smaller shanks. RSS screws that are 3-1/8 in and longer have CEE threads which enlarge the screw hole for the non-threaded portion of the fastener, allowing the wood to settle easily and increases the screw's drawing strength. The CEE thread also reduces the friction on the screw shank which can result in lowering the driving torque and the likelihood of splitting the wood. This is why the RSS screw is an efficient lag screw alternative. Our round head with built-in shield (washer type head) has no sharp edges like conventional lag screws. The added shoulder (nominal diameter) underneath the washer has the ability to center the RSS screw in pre-drilled hardware like hinges and connector plates.
- Diameter: 5/16"
- Length: 2-1/2"
- Count: 100
- Recessed star drive zero stripping, with six points of contact
- CEE Thread enlarges hole to reduce splitting
- W-Cut low torque, faster drive
- Zip-Tip no pre-drilling, faster penetration
- Washer head for immense holding power
- Cutting pockets provide a clean hole and reduces splitting and bore with precision
- Case hardened steel for high tensile, torque and shear strength
- Climatek coating is AC257 code approved for use in treated lumber
- ESR-2442 Approved for structural application
View Details
Call for Price
R4 FRAMING SCREW 8 x 1-1/2" 5-LB
GRK's RSS screw is made of specially hardened steel to provide you with high tensile, torque and shear strength. The sharp threads and points bite instantly into the material (including hardwood), reducing the splitting effect due to smaller shanks. RSS screws that are 3-1/8 in and longer have CEE threads which enlarge the screw hole for the non-threaded portion of the fastener, allowing the wood to settle easily and increases the screw's drawing strength. The CEE thread also reduces the friction on the screw shank which can result in lowering the driving torque and the likelihood of splitting the wood. This is why the RSS screw is an efficient lag screw alternative. Our round head with built-in shield (washer type head) has no sharp edges like conventional lag screws. The added shoulder (nominal diameter) underneath the washer has the ability to center the RSS screw in pre-drilled hardware like hinges and connector plates.
- Diameter: 5/16"
- Length: 2-1/2"
- Count: 100
- Recessed star drive zero stripping, with six points of contact
- CEE Thread enlarges hole to reduce splitting
- W-Cut low torque, faster drive
- Zip-Tip no pre-drilling, faster penetration
- Washer head for immense holding power
- Cutting pockets provide a clean hole and reduces splitting and bore with precision
- Case hardened steel for high tensile, torque and shear strength
- Climatek coating is AC257 code approved for use in treated lumber
- ESR-2442 Approved for structural application
View Details
Call for Price
R4 FRAMING SCREW 9 x 2" 5LB
GRK's RSS screw is made of specially hardened steel to provide you with high tensile, torque and shear strength. The sharp threads and points bite instantly into the material (including hardwood), reducing the splitting effect due to smaller shanks. RSS screws that are 3-1/8 in and longer have CEE threads which enlarge the screw hole for the non-threaded portion of the fastener, allowing the wood to settle easily and increases the screw's drawing strength. The CEE thread also reduces the friction on the screw shank which can result in lowering the driving torque and the likelihood of splitting the wood. This is why the RSS screw is an efficient lag screw alternative. Our round head with built-in shield (washer type head) has no sharp edges like conventional lag screws. The added shoulder (nominal diameter) underneath the washer has the ability to center the RSS screw in pre-drilled hardware like hinges and connector plates.
- Diameter: 5/16"
- Length: 2-1/2"
- Count: 100
- Recessed star drive zero stripping, with six points of contact
- CEE Thread enlarges hole to reduce splitting
- W-Cut low torque, faster drive
- Zip-Tip no pre-drilling, faster penetration
- Washer head for immense holding power
- Cutting pockets provide a clean hole and reduces splitting and bore with precision
- Case hardened steel for high tensile, torque and shear strength
- Climatek coating is AC257 code approved for use in treated lumber
- ESR-2442 Approved for structural application
View Details
Call for Price
R4 FRAMING SCREW 9 x 2-1/2" 5LB
R4 FRAMING SCREW 9 x 2-1/2" 5LB
View Details
Call for Price
R4 FRAMING SCREW 9 x 3-1/8" 5LB
R4 FRAMING SCREW 9 x 3-1/8" 5LB
View Details
Call for Price
R4 FRAMING SCREW 10 x 4" 5LB
R4 FRAMING SCREW 10 x 4" 5LB
View Details
Call for Price
RT TRIM HEAD SCRW 8 x 2-1/2" 5LB
RT TRIM HEAD SCRW 8 x 2-1/2" 5LB
View Details
Call for Price
RT TRIM HEAD SCRW 8 x 3-1/8" 5LB
RT TRIM HEAD SCRW 8 x 3-1/8" 5LB
View Details
Call for Price
TRIM HEAD SCRW 8 x 1-1/2" 100PC
TRIM HEAD SCRW 8 x 1-1/2" 100PC
View Details
Call for Price
RT TRIM HEAD SCRW 8 x 3-1/8" 100
RT TRIM HEAD SCRW 8 x 3-1/8" 100
View Details
Call for Price
TRIM HEAD SCRW 9 x 5" 50PC
TRIM HEAD SCRW 9 x 5" 50PC
View Details
Call for Price
